FREQROL E500 MANUAL PDF

Offline Auto Tuning Function pr. Fr-esc to sc-ene; fr-essc to sc-ene 38 pages. If a data error is detected and a retry must be made, execute retry operation with the user program. Enter text treqrol picture: It can not be measured accurately with a meter or general instrumentation. Base Frequency, Base Frequency Voltage pr.

Author:Faeshakar Kishakar
Country:Bosnia & Herzegovina
Language:English (Spanish)
Genre:Career
Published (Last):10 November 2010
Pages:187
PDF File Size:6.39 Mb
ePub File Size:3.34 Mb
ISBN:323-3-53754-652-6
Downloads:49867
Price:Free* [*Free Regsitration Required]
Uploader:Karisar



Offline Auto Tuning Function pr. Fr-esc to sc-ene; fr-essc to sc-ene 38 pages. If a data error is detected and a retry must be made, execute retry operation with the user program. Enter text treqrol picture: It can not be measured accurately with a meter or general instrumentation.

Base Frequency, Base Frequency Voltage pr. Do not connect terminal SD of the inverter with terminal 0V of the external power supply. Table of Contents Add to my manuals Add.

Always read the instructions before using the equipment 6. The multi-speed settings override the main speeds across terminals Page 26 10cm 3.

To ensure safety, connect the power input to the inverter via a magnetic contactor and earth leakage circuit breaker or no-fuse breaker, and use the magnetic contactor to switch power on-off. Overload OL monitor rotation Set necessary parameter freqro according to the load and operating specifications.

Load Pattern Selection pr. Surge voltages attributale to the wiring constants may occur at the motor terminals, deteriorating the insulation of the motor. Page — Slip compensation Pr. Do not run the inverter with the front cover removed. Page — Regenerative brake duty Pr. Handle the inverter properly in accordance with the information in each section as well as the precautions and instructions of this manual to use it correctly.

When the carrier frequency exceeds 5kHz, do not use the instrument because overcurrent losses occurring in the metallic parts inside the instrument will increase and may lead to burnout. The following list indicates purpose of use and corresponding parameters. Comments to this Manuals Your Name. The earth leakage circuit breaker should be installed to the primary power supply side of the inverter. Page — Troubleshooting Page — Speed greatly differs from the setting Page — Operation mode is not changed mamual Page — Precautions for Maintenance and Inspecti Thank you for choosing the Mitsubishi Transistorized inverter.

Computer Link Operation pr. This instruction manual gives handling information and precautions for use of this equipment. Press the key, to choose the MODE parameter setting mode.

Operation mode can be switched to PU operation mode. Page 64 3 Combined operation mode 1 Pr. The power supply janual size of the AC reactor range motor indicated assumes that its length is 20m Page 90 — Base frequency, base frequency voltage Page 91 — Multi-speed operation Pr.

Appendix 1 Data Code List Always read the instructions before using the equipment. Check the corresponding areas.

Page Page — User group selection Pr. The set point is given to across inverter terminals V. If the operation mode cannot be changed, refer to page Prepare equipment and parts as necessary. Note that motor noise increases. TOP 10 Related.

LAGARTA HELICOVERPA ARMIGERA PDF

Mitsubishi Freqrol E500 Manual ภาษาไทย

Mikagore To change the external operation mode Pr. Otherwise, you may access the exposed high-voltage terminals or the charging part of the circuitry and get an electric shock. Otherwise, the detection signal may not be output manuaal torque is not generated at a low output current. Their characteristics are adversely affected by ripple current, etc. Push either A or B in the direction of arrows, and using the other end as a support, pull the front cover toward you to remove.

BLOCHER PRINZIP PDF

FR-E700 Overview

Akitaur Parameter Write Inhibit Selection pr. This may cause a gravity drop when the inverter is used in vertical lift application. Appropriate peripheral devices must be selected according to the capacity. When entering 0 to 10VDC, always make this setting. The calibration values are not initialized.

Related Articles